1. Always use STERILE TECHNIQUE
2. ASSUME that any bacteria that grows on your plate is harmful and treat as such
3. Always WASH HANDS after you are finished handling plates
-Prepoured Agar Plates
- Known Cultures, Gram + and -
-Gram Stain Kit
Essential Question: What kinds of bacteria are found on surfaces?
1. Inoculate plates with samples from surfaces at the school and observe growth of bacteria colonies.
2. Analyze colonies and attempt to identify single bacterium within the colonies under a microscope.
3. Compare your sample to known samples of bacteria, investigating where these known samples are likely to be found.
4. Perform a gram stain on known bacteria and compare to your unknown sample.
**This lab may take several days, keep all data and observations in a separate notebook to be compiled and organized into a final lab report.
A solid source for bacterial growth is essential if organisms are to be isolated. In the laboratories of Robert Koch, gelatin was first used to achieve bacteria colonies. Agar now serves as a more useful material; it will remain solid until heating and then will solidify as it cools. Before it cools (and solidifies) it can be poured into petri dishes. Using sterile technique minimizes the contamination of the agar before you are ready to inoculate it with bacteria from other sources.
Your agar plates will be prepared for you in advance.
Without opening any of the petri dishes, use a marking pen to divide the dish into four quadrants and label the sections as shown on the bottom of the plates.
Surface 1: Any surface in classroom, hall or bathroom. Use sterile cotton swabs.
Surface 2: Any surface in classroom, hall or bathroom. Use sterile cotton swabs.
D: Touch your finger gently to this circle.
C: Clean your finger with an alcohol pad or soap and touch it to this sector.
You will identify and categorize different bacterial colonies based on varied appearance and morphology (form and structure), When a single bacterial cell is deposited on the surface of a nutrient medium (agar), it begins to divide exponentially. After thousands of cells are formed, a visible mass appears which is called a COLONY. Each species of bacteria will exhibit characteristic colonies.
1. Draw each plate, showing how colonies are spread across the agar surface.
2. Pick several colonies on your plates and describe them using the terms above.
3. (Optional) You may wish to photograph your plates and include them in your final lab report.
1. Place a drop of water on a clean slide.
2. Heat the inoculating loop until it glows red. Let it cool then remove a small amount of culture from the agar surface; touch it several times to the drop of water until it just turns cloudy.
More is not better! Too much and you won't be able to see individual cells
3. Burn the bacteria from the loop and allow the loop to cool, use the loop to spread the suspension (water + bacteria) over the surface of the slide to form a thin film.
4. Allow suspension to air dry. This process will be short if you spread the liquid out in step 4.
5. Hold the slide with a clothespin and then heat fix the bacteria on the slide by passing it over the flame 3-4 times (film side up). Do not overheat the slide, it should feel warm but not hot.
6. Place a drop of methylene blue on the slide over where the “smudge” of bacteria and water is
7. Allow the dye to remain for approximately 1 minute (the bacteria will take up the stain during this time)
8. Wash the excess stain off the slide by picking the slide up and holding it at an angle over the sink. Gently rinse the excess dye off with water.
9. Blot off excess stain and water using filter paper - DO NOT RUB!
10. Examine the slide under the microscope using the high power objective. You do not need a coverslip.
You may need to repeat this process a few times in order to get a good slide!
*Identify the shape and arrangement of the bacteria. Make sketches of each to include in your final lab report.
Use internet sources, slide viewers, and prepared slides to identify the different shapes and types of bacteria. Your investigation should include, but not necessarily be limited to the following well-known bacteria.
1. Escherichia coli
2. Staphylococcus aureus
3. Bacillus subtilis
4. Cholera vibrio
*Include sketches and descriptions in your final lab report as well as an overview of the bacteria. This is something you may need to research on your own.
Microbiologists use a special level of classification to describe eubacteria – it is called the “Division”. Eubacteria are placed in a division depending on the type of cell wall they have. A bacterium with a cell wall that has a large amount of petidoglycan, is classified as gram (+) and stains blueish-purple. Bacteria with a thin peptidoglycan layer are classified as gram (-) and will stain pink.
Gram stains can be difficult and take practice. Follow the steps exactly as listed. If done correctly, you should be able to identify your bacteria as Gram + or Gram - and check resouces to see if you are correct. If known samples are not available, you can gram stain a sample from your petri dish, but there will be no way to check your accuracy.
1. Add a sample of a known culture to your slide and pass it briefly over flame to heat fix the sample.
2. Add 5 drops of crystal violet over the fixed culture. Let stand for one minute.
3. Pour off excess stain and gently rinse the slide in tap water. Keep in mind, the objective is to wash off the stain, not the fixed culture.
4. Add about 5 drops of iodine to the smear. Let stand for one minute.
5. Pour off excess iodine and rinse the slide with water as before.
6. Tip the slide and add several drops of the ethyl alcohol to the upper end. Allow alcohol to flow over the smear. After several seconds, rinse the slide again.
7. Add about 5 drops of the safranin to the slide. Let stand for one minute.
8. Rinse the slide again, drain and blot away excess moisture. Let the slide dry.
Compare each of the samples colors, taking note of whether the sample a light pink color (gram -) or a dark purple color (gram +). Don't forget to write down the names of your samples to include in your lab report later.
If your gram stain was not successful, use google to research your sample and find out what it is.
Review the "Goals" listed at the beginning of this document. Your job is to demonstrate that you have achieved these goals.
1. Title (Something clever)
2. Purpose – Describe the objectives of this activity.
4. Conclusions – What did you learn? What would you like to do over or expand upon? This is the area for your own reflections and thoughts.
Introduction (interesting, includes goals) __3 __2__1__0
Colonies (descriptive) __3 __2__1__0
Bacteria Comparisons __3 __2__1__0
Gram Stain (procedure, ID) __3 __2__1__0
Overall Demonstration of Goals __3 __2__1__0